Single phase Servo Drivers CD 420

PDFPrintEmail

  • Power Supply Voltage: AC220V±20% 47-63Hz

  • Rated Output Power: 0.2-0.75KW

  • Dimensions: 166x141x61mm

___________CD420_4edca75c71190.jpg
Sales price without tax 332,00 €
Price / kg:
Rated Power
___________CD420_4edca75c71190.jpg
CD 420.jpg
Description
Model CD420
200W - 750W
Power Main Supply Voltage Single-Phase AC220V±20% 47~63Hz
Control Circuit Voltage DC24V 1A
Current Rated Current(RMS) 4A
Peak Current(PEAK) 15A
Feedback Signal 2500PPR (Incremental Encoder with 5V Supply and RS422 Signals)
Brake Chopper Use an External Braking Resistor if Necessary
Brake Chopper Threshold DC380V±5V
Over-Voltage Alarming Threshold DC400V±5V
Under-Voltage Alarming Threshold DC200V±5V
Cooling Method Natural Air Cooling
Weight 1.2kg
Position
Mode
Max. Frequency of Input Pulse Differential Signal: 500KPPS, Open-Collector Signal: 200KPPS
Pulse Command Mode Pulse+Direction, CCW+CW, (higher Voltages than 5V Need External Current Limiting Resistors)
Command Smoothing Low-Pass Filtering(Internal Parameters)
Feedforward Gain Internal Parameters
Electronic Gear Ratio Setting Range, Gear Factor: -32768~32767, Gear Divider: 1~32767, 1/50≤|Gear Factor/Gear Divider|≤50
Position Loop Sampling Frequency 1KHz
Speed
Mode
Analog Input Voltage Range 0 ~±10V(Resolution 12bit)
Input Impedance 200K
Analog Input Sampling Frequency 4KHz
Command Source External Analog Command/Internal Command
Command Smoothing Low-Pass Filtering(Internal parameters)
Input Voltage Dead-Zone Setting Internal Parameters
Input Voltage Offset Setting Internal Parameters
Speed Limit Internal Parameters
Torque Limit Internal Parameters / External Analog Command Control
Speed Loop Sampling Frequency 4KHz
Torque
Mode
Analog Voltage Input Range 0 ~±10V (Resolution 12bit)
Input Impedance 200K
Input Sampling Frequency 4KHz
Command Source External Analog Command/Internal Command
Command Smoothing Low-Pass Filtering(Internal Parameters)
Speed Limit Internal Parameters /External Analog Command Control
Input Voltage Dead-Zone Setting Internal Parameters
Input Voltage Offset Setting Internal Parameters
Current Sampling Frequency 16KHz
Digital
Input
Input Specification 7 Digital Inputs, With COMI Terminal for PNP or NPN Connection.
Input Function Define Freely According to Requirement, Supporting Following Functions: Driver Enable,Driver Fault Reset,Driver Mode Control,Proportional Control, Forward Inhibit Limit, Reverse Inhibit Limit, Negative Limit Position,Home Signal, Speed Command Reverse, Internal Speed or Position Select
Digital
Onput
Output Specification 5 Digital Outputs,OUT1~OUT4 Current is 100mA,OUT5 Current is 800mA
Output Function Define Freely According to Requirement, Supporting Following Functions: Driver Ready, Driver Fault, Position Reached, Motor at Zero Speed, Motor Brake, Motor Speed Reached, N Signal
Protection Functions Over-Voltage Protection,Under-Voltage Protection,Motor Over-Heat Protection(I²T),Short-Circuit Protection,Drive Over-Heat Protection,etc.
Communication Interface RS232
Operation
Environment
Operating Temperature 0~40℃
Storage Temperature -10℃~70℃
Humidity(Non-Condensing) 5~95%
Protection Class IP20
Installation Environment Installed in a Dust-Free,Dry and Lockable Environment(Such as in a Electrical Cabinet)
Installation Mode Vertical Installation
Height Below 1000m
Atmospheric Pressure 86kpa~106kpa

 

CD Servo System